6. Insulation with Rock Wool Batts. Easy to handle and pre-fabricated batts with a thickness or depth of 11.25″ will be needed to attain an R-value of R38. It is used in floors of crawlspaces and attics, supplying water-resistant insulation with no forming of mildew, fungi, or mold.

What is R-38 insulation used for?

R-38C EcoTouch® Thermal Batt insulation is intended to be friction- fit between wood rafters. In applications with irregular spaced rafters, cut the batts approximately ½ ” wider than the space and friction fit them in place. Tightly abut batts to prevent thermal leaks. Provide vent openings at the eave and ridge.

Is R38 insulation good for attic?

The thicker the insulation, the greater/higher it’s R-value and performance. As of 2016, the standard building code for attic insulation in L.A., Orange, Ventura and surrounding counties is R-38.

What is the depth of R38 insulation?

An R-38 fiberglass batt should be approximately 12 inches thick, while the thickness of cellulose insulation of a finished, fitted product will larger.

What kind of insulation is R38?

R38 – 12 in – Fiberglass Insulation – Insulation – The Home Depot.

What is the difference between R38 and r49 insulation?

A ceiling with an R-value of 38 lets through only 1/38 of the amount of energy per square foot that passes through that window, or about 2.6 % of the energy; a ceiling with an R-value of 49 lets through only 1/49 of the amount of energy per square foot that passes through that window, or about 2.0 % of the energy.

Which insulation is best for attic?

Fiberglass, cotton, and mineral wool can all work as loose-fill material, but the far and away top choice for blown-in insulation is fiberglass. Contrary to batts, blown-in fiberglass insulation is perfect for filling in tight voids around wiring, pipes, or any area with awkward framing.

Can you have too much insulation in an attic?

Can you over insulate your attic? The answer is yes! Past a certain point, insulation in a vented attic will do more harm than good. In most of the United States, achieving an R-Value of 38 is more than sufficient.

What R-Value is needed for ceiling insulation?

Depending on where you live and the part of your home you’re insulating (walls, crawlspace, attic, etc.), you’ll need a different R-Value. Typical recommendations for exterior walls are R-13 to R-23, while R-30, R-38 and R-49 are common for ceilings and attic spaces.

What insulation has the highest R-value?

Vacuum insulated panels have the highest R-value, approximately R-45 (in U.S. units) per inch; aerogel has the next highest R-value (about R-10 to R-30 per inch), followed by polyurethane (PUR) and phenolic foam insulations with R-7 per inch.

What is the highest R-value for a 2×4 wall?

Cavity insulation, like framing, has options. A 2×4 wall cavity can be insulated from R-13 to roughly R-25. A 2×6 wall can be insulated from R-19 to R-39.

What is the R-value of 2 inch foam board?

A wall utilizing STYROFOAM T-MASS Technology with a 2-inch exterior layer and a 4-inch interior layer of concrete along with a 2-inch layer of STYROFOAM extruded polystyrene insulation would result in a material R-value of approximately 11.33.

How thick is R38 rigid insulation?

Easy to handle and pre-fabricated batts with a thickness or depth of 11.25″ will be needed to attain an R-value of R38. It is used in floors of crawlspaces and attics, supplying water-resistant insulation with no forming of mildew, fungi, or mold.

How do you get a R38 on the ceiling?

An insulation value of R-38 is at the high end and requires a minimum thickness of 12 inches. R-value does not depend on a single layer of insulation. To achieve R-38, you can use two layers of R-19 or three layers of R-13, which give slightly higher thermal resistance.

What is the R-value of 12 inches of blown insulation?

The number is presented per inch, so an R-value of 3.1 at 12 inches would provide an overall value of R-38.