Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.

Is there a reset button on a washing machine?

Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.

How do I reset my washing machine?

To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.

How do I reset my Whirlpool front load washer?

Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.

How do I reset my Whirlpool washing machine?

Method 1: Unplug it The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.

How do I fix my washing machine it wont turn on?

How to Fix a Washing Machine that Won’t Start

1. Activate the power button.
2. Test the outlet.
3. Reset outlet if necessary.
4. Make sure the power cord is plugged in.
5. Check if fuses are blown or the circuit breaker is thrown.
6. See if Delay Start has been pushed.
7. See if Control Lock has been activated.

What causes a washing machine to stop working?

There are a few possible reasons for this: – The locking mechanism could have jammed (maybe some clothes have gotten in the way). – There could be a glitch in the washer’s computer. – The washing machine may not be draining properly, leaving the washer door locked and the drum filled with water.

Why is my washing machine not turning on?

Make sure the machine is tightly plugged in. Next, check for a tripped circuit breaker. Reset the breaker and try to start the washer. If neither is at fault, you may have a damaged power cord.

How do you test a washing machine fault?

How to Check to see if your Washing machine bearings are worn.

1. Appliance is leaking.
2. Appliance will not start.
3. Clothes are damaged after washing.
4. Clothes are still dirty.
5. Door will not open at end of programme.
6. Drum will not rotate.
7. Machine overfills and floods.
8. No water entering machine.

How do I reset my top load washer?

Motor Reset Procedure:

1. Unplug the washer for 1 minute from the electrical outlet.
2. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid.
3. The motor has now been reset and is ready for you to start a cycle.

What causes a washing machine not to drain and spin?

If your washer won’t drain or spin, the water level control may be faulty. Open the machine’s control panel and look for a plastic tube attached to the water level valve. If it’s clogged, clear it out with vinegar. If the valve itself is corroded, it may need to be replaced.

Why does my Whirlpool washer not start?

One reason your appliance may not start is that it has simply come unplugged or that the outlet that it is plugged into has tripped your home’s main circuit breaker. If you notice a tripped breaker, leave the breaker off and carefully inspect the electrical outlet and power cord for any sign of a problem.

Where is the control lock button on Whirlpool washer?

When you are ready to resume use of the washer, you must first unlock the control panel.

1. Locate the “Control Lock/Unlock” button on your Duet’s control panel.
2. Press and hold the “Control Lock/Unlock” button for three seconds.
3. Release the “Control Lock/Unlock” button when the control lock icon on the display disappears.